Dealing With False Alarms From ADT Home Security Systems

It’s midnight. You’re on the road, and your ADT home security app sends you a push notification. Your burglar alarm just went off. You don’t know why — a glitch, a burglar, or your 90-pound Dalmatian — but you know the entire block is awake now. If you’re on a premium professional monitoring plan, you may even be getting a visit from the police. What do you do?

Well, first, you can relax. Chances are it’s a false alarm. The stats are a little dated, but in 2004, for example, out of 62,000 police visits to residences in Dallas, Texas, where alarms had gone off, a mere 2.8 percent were crimes in progress.1 That may be a relief if you were biting your nails at the airport at the thought of a thief pillaging your living room, but false alarms are a massive drain on police departments and first responders.2 Depending on where you live, repeated false alarms (burglar or fire) will also cost you — usually between $50 and $100 a pop for the first violation.

In this home security guide, we’ll drill down into ADT security system false alarms — how they come about, what to do if you’re experiencing them, and why you should take them seriously.

ADT Security System False Alarms: Common Causes

There are a lot of things that can send your ADT security system into a tizzy. Some of them are the typical head-slappers. Your kids forgot the alarm was armed and barged into the kitchen. Bam! Or your house sitter fumbled the code. Hopefully, that won’t happen too often.

But alarm failures can also get technical, or at least the nature of the problem may not be evident. Your hub could have an installation issue, fooling your system into thinking someone has been tampering with it by trying to dislodge it or cut the wires. Once that happens, your ADT security system could start shrieking the minute you touch it — and you’d have no idea why.

As far as technical issues go — assuming your wiring isn’t to blame — there are three main categories to troubleshoot when your ADT home alarm or smoke detectors start crying wolf: motion sensor issues, door or window (entryway) sensor issues, and glass-break sensor issues. Let’s start with motion sensor issues because they’re pretty common.

Motion Sensors

ADT’s motion detectors use passive infrared (PIR) sensors to detect suspicious movement in your house. They’re not only watching for movement, but they’re also looking for the movement of heat. What does that mean for your 86-decibel ADT burglar alarm?

If one of your motion sensors is going bonkers, and you’ve ruled out a low battery or a wiring issue, it could be that some random motion in the room is triggering it. Swaying blinds, a heavy pet, or a tiny critter crawling over the sensor are the usual suspects. But your problem could also be heat-related.

If it’s scorching hot inside and your sensor’s threshold is set too low, a hot breeze could trick your motion detector into thinking it’s an intruder. Sounds crazy, but it happens. Here’s a deeper dive into how motion sensors work. Read on for some solutions to your ADT motion sensor woes.

Door and Window Sensors

Diagnosing door and window sensor issues is a bit more straightforward than pinpointing the problem with a wonky motion sensor. Each entryway sensor comes with two parts: a magnet and a switch. As long as your doors and windows are closed tight and those two parts are properly aligned (see photo above), a current will flow between the switch and the magnet, forming a circuit. When something happens to separate the two parts, the switch opens and the current stops, sending an instant message to your alarm that you have an unwanted visitor.

But you have an ADT security system. A professional electrician installed it. You shouldn’t be having technical issues like that, right?

Even with the best professionally installed home security systems — and, in our book, ADT is one of them — door and window problems can crop up that could affect your alarm. You’ve had work done inside the house, say. Or maybe over time your windows and doors have started sagging and no longer close properly. It’s possible that your self-adhesive sensors have become unstuck. In any of those scenarios, you may be plagued by costly false alarms.

Glass-Break Sensors

Glass-break sensors are the most temperamental equipment on this list — for a good reason. Noise trips them. Specifically, noise at the same pitch as glass breaking. That could be your dog barking, thunder booming, or even a TV explosion.

That’s not very comforting news if you just bought a couple of glass-break sensors thinking you’d added the perfect finishing touch to your home security arsenal, but instead got an 85-decibel headache every time the dog barks — not to mention a possible visit from the men in blue if you’re out and don’t catch the false alarm on your ADT+ app. Yikes! Definitely not great, but not the end of the world either. You may just need to make a few simple adjustments to your home security setup.

What to Do About ADT Security False Alarms

First things first: If your ADT alarm starts blaring and you’re sure it’s crying wolf, you should deactivate it. You’ll get a call from ADT next. Let them know the situation is under control. When DEFCON 1 is safely and quietly back at DEFCON 5, you can start troubleshooting. Here’s a pocket guide to ADT alarm hygiene.

Recognize Low Batteries

When your ADT batteries are low, you’ll see one of the following warnings on your hub: BAT, LOW BATT, or SYSTEM LO BAT. If one of your sensors is the issue, you should see the zone number as well.

Educate Kids and Visitors

House sitters, babysitters, grandmas, and even your own kids should at least be able to tell what an armed hub looks like. If you’ve got regular visitors or a guest staying for a while, you’ll want to lead them through the arming/disarming ritual before you let them loose in your home. As you no doubt know, once that high-pitched warning sounds, your fingers get wobbly and it’s hard to think straight.

Don’t Forget Your System Tests

Running a system test lets you test all your ADT sensors without triggering an actual alarm. We recommend doing it at least once every few months, or after a power outage or any electrical work.

If you’ve got a MyADT account, log in, find Alarm System > System Test, and click Start System Test.

If you’re comfortable with the ADT+ app, find Monitoring in the main menu, and then click Monitoring Test Mode. In both cases, you’ll need to specify a test duration.

Check Windows and Doors

You already know if your entryway sensor magnets aren’t lined up with their switches, the circuit is broken and your ADT security system thinks you have an intruder. Alignment issues aren’t blue-moon events. Windows buckle. Doors sag. You can nip this ear-splitting fiasco in the bud by checking on the state of your doors and windows every six months to a year.

Set and Position Your Motion Sensors Properly

A nearby ceiling fan or heater can trigger a sensitive motion sensor as easily as a heavy pet. The best home security systems we’ve tested this year let you calibrate their security cameras and motion detectors to avoid tripping false alarms. ADT’s motion sensors, specifically, are what we call “pet immune,” meaning they’re geared to ignore anything under 80 pounds.

That said, if you have pets — even small ones — you should still position your sensors high enough on the wall that a sudden leap from your kitty won’t trigger “alarmageddon.”

Final Thoughts: Why You Should Avoid Setting Off False Alarms

Back in 2007, when the last major study came out, the DOJ reported that false alarms cost taxpayers nearly $2 billion per year in wasted police resources. They also cost homeowners plenty in yearly permit fees and fines that in some states started at 100 bucks per false alarm.

Financial damage aside, the heaviest toll this barrage of backfiring alarms has taken on our communities is in personal security. If a cop shows up at your door 12 times in a row because your babysitter tripped the alarm, do you expect them to rush over on the 13th, when an actual intruder has broken into your home?

Paying for permits is a nuisance, but feeling insecure in your own home — a home you already pay hundreds of dollars a year to protect with professional security services — because the police are tired of responding to false alarms? That’s a crying shame. It also happens to be the real reason we should all take care to avoid false alarms at all costs.

OK, lecture over.